Convert SPH to EAC3

Turn SPH recordings into EAC3. Encoded as Dolby Digital Plus (E-AC-3) at 192 kbit/s and at 32, 44.1 or 48 kHz with up to 5.1 channels, unless audio.bitrate, audio.sample_rate or audio.channels say otherwise.

Converted in an isolated sandbox on our serversDeleted after 24 hours

Drop SPH files on the dialor turn it to pick what to do

Speech recordings as Dolby Digital Plus.One EAC3 file at 192 kbit/s, ready for players that take surround sound.

  1. What you get

    A single E-AC-3 file made from your SPH recording. It is encoded as Dolby Digital Plus at 192 kbit/s, at 32, 44.1 or 48 kHz, with up to 5.1 channels.

    Those values apply unless you set Audio bitrate (kbit/s), Sample rate (Hz) or Channels to something else. See every EAC3 conversion for other ways to reach this format.

  2. Bitrate, rate and channels

    Set Audio bitrate (kbit/s) from 64 to 320. 128 is fine for speech and casual listening, and 192 to 320 suits music. A higher bitrate makes a bigger file.

    Set Channels to 1 to mix the sound down to mono, which halves its size and suits speech. Set it to 2 to keep stereo. Set Sample rate (Hz) between 32000 and 48000. A lower rate makes a smaller file and dulls high sounds.

  3. Clean up and adjust

    Turn on Reduce noise to lower steady background noise such as hum, hiss and fans. Sudden noises such as a door are left in.

    Turn on Normalize loudness to bring quiet and loud recordings to -16 LUFS. Normalizing also resamples to 44.1 kHz unless you set Sample rate (Hz).

    Set Speed from 0.25 to 4 to play faster or slower, and voices keep their pitch. Set Pitch from -12 to 12 semitones to move the pitch while the speed stays the same.

  4. Trimming

    Set Start at (s) to cut that many seconds from the beginning. Decimals such as 1.5 work. Set Stop at (s) to end at that second of the original.

    Stop at (s) counts from the start of the original, not from where trimming starts, so it must be later than Start at (s).

SPH and EAC3.What each format is, and the options this conversion takes.

  1. 01 · audio.bitrate

    Audio bitrate (kbit/s)

    How much data each second of sound gets. 128 is fine for speech and casual listening, 192 to 320 for music. Higher makes a bigger file.

    64 to 320
  2. 02 · audio.channels

    Channels

    1 mixes the sound down to mono, which halves its size and suits speech. 2 keeps it stereo.

    1 to 6
  3. 03 · audio.denoise

    Reduce noise

    Lowers steady background noise such as hum, hiss and fans. Sudden noises such as a door are left in.

  4. 04 · audio.normalize

    Normalize loudness

    Makes quiet and loud recordings play at the same loudness, -16 LUFS, the level podcasts and streaming services aim for.

  5. 05 · audio.pitch

    Pitch

    Moves the pitch up or down by whole semitones while the speed stays the same. 12 is one octave up and -12 one octave down.

    -12 to 12
  6. 06 · audio.sample_rate

    Sample rate (Hz)

    How many times per second the sound is measured. 44100 is the CD rate and 48000 the video rate. Lower makes a smaller file and dulls high sounds.

    32000 to 48000
  7. 07 · speed

    Speed

    Plays faster or slower. 2 is twice as fast and 0.5 half as fast. Voices keep their pitch.

    0.25 to 4
  8. 08 · trim_end

    Stop at (s)

    Stops at this second of the original. It counts from the start of the original, not from where trimming starts, so it must be later than Start at.

    0 to 86400
  9. 09 · trim_start

    Start at (s)

    Cuts this many seconds from the beginning. Decimals such as 1.5 work.

    0 to 86400

The formats

From · SPH

NIST SPHERE Audio

Speech recordings in the NIST SPHERE format of the TIMIT and LDC speech corpora.

Extensions
.sph
MIME type
audio/x-nist-sphere
Kind
Audio
To · EAC3

E-AC-3 Audio

Dolby Digital Plus audio, the surround sound of streaming services and Blu-ray.

Extensions
.eac3 .ec3
MIME type
audio/eac3
Kind
Audio

In your code.The same SPH to EAC3 conversion through the API, for your app or your agent.

terminal
$ cv convert recording.sph recording.eac3
$ cv convert recording.sph recording.eac3

Questions.What people ask about SPH to EAC3.

01OF 04

192 kbit/s, unless you set Audio bitrate (kbit/s). The option accepts 64 to 320.

Yes. Set Channels to 1 to mix the sound down to mono. This halves the size and suits speech.

Yes. Normalize loudness also resamples to 44.1 kHz unless you set Sample rate (Hz).

Yes. Set Start at (s) and Stop at (s). Stop at (s) counts from the start of the original and must be later than Start at (s).

More conversions.Other ways in and out of SPH and EAC3.